h a l f b a k e r yFaster than a stationary bullet.
add, search, annotate, link, view, overview, recent, by name, random
news, help, about, links, report a problem
browse anonymously,
or get an account
and write.
register,
|
|
|
Power grid timestamp
Subtly vary frequency of electrical grid to provide a reliable timestamp for consumer devices | |
So basically, you set up your power distribution hardware at the generation source to vary the frequency of the electricity in the grid by some arbitrary but small range so that any mains powered consumer device can determine the time without maintaining an internal clock.
I don't know the sensetivity,
but for arguments sake let's say that from 00:00 to 23:59, the frequency varies at a linear progression from 49hz-51hz. A simple and non-variable comparator circuit could then deduce the time at any point connected with the power grid to within a second or two.
Could be used to remove unreliable PV circuits in public lighting circuits. Could be used so all your clocks stay on time. Could be used by home computers, electric hot water heaters, any number of devices to reliably determine time in order to trigger or control some other process.
Inspired by [kansan101]'s smart bulbs idea.
Please log in.
If you're not logged in,
you can see what this page
looks like, but you will
not be able to add anything.
Annotation:
|
| |
Most computers and mobile phones check off an internet-
based clock system already, no? |
|
| |
Yep, you're right. But many other appliances and systems aren't. |
|
| |
Could probably do this with a secondary signal on top of the main 50Hz instead of frigging around with the primary frequency - however I figure that distribution hardware and interference, etc would make that more difficult or harder to maintain accuracy. |
|
| |
Hmm, I thought it was held very stready due to frequency sensetive devices and the voltage-frequency relationship of the alternators, not for any other purpose. I used to work in a regional power station (off main grid) and we had much management equipment in place to maintain stable frequency - but there was still an error range. |
|
| |
So are you saying consumer goods do a sum of cycles to determine the time after a given reset event, or that they use the mains frequency as a heartbeat for their internal clocks? |
|
| |
My idea is intended that a device could tell the time of day *anytime* and *instantly* by comparing mains frequency to a given internal standard frequency - no clock mechanism needed. Similar purpose, but not the same as you describe unless I've very much misinterpreted what you said. |
|
| |
Isn't there an effort to smooth power output so as not to
damage devices? |
|
| |
Go to 60 Hz. You're clearly getting more cycles for
your money, which every good marketing agent
knows is a better value. Imagine the time savings as
your clocks run faster... |
|
| |
[bigs] I assume (hope!) it has not been relaxed - there must be lots of those mains powered wall clocks which use the AC to run a motor, and which need a long term average of exactly 50hz to keep good time? I read that they deliberately sped up or slowed down the frequency overnight to maintain the average. |
|
| |
Just today I was calibrating an old record player with a stripey disc and an incandescent mains-powered lightbulb. |
|
| |
Data over power is fairly WKTE, but it generally uses
very high frequency small amplitude variation
stacked on top of the main (50 or 60 hz) frequency.
Most equipment filters this out by it's very nature. |
|
| |
Varying the mains frequency does tend to mess up
equipment, it can increase the burn-out rate of
motors or cause equipment (some of which still uses
clipped wall frequency to provide a timing pulse) to
run off-speed. |
|
| |
I don't think you'd need to vary the frequency by
even 1Hz. Cheap timing circuits should be able to
measure frequency to within a tiny fraction of a
Hertz. |
|
| |
However, the main problem is that mains
frequency varies quite widely, depending on load
and on which generators are on- and off-line. So,
a clear signal would have to vary the frequency by
more than the greatest amount of 'random'
variation. |
|
| |
Of course, you could use frequency variation to
encode things more subtly. For example, five
cycles advanced by 100µs and then five cycles
retarded by 100µs; this would be detectable and
probably discriminable from random fluctuations.
But it would be very difficult to inject that kind of
short-term variation into the supply, since mains
frequency generally depends on the rotational
speed of big heavy things. |
|
| |
Probably easier to superimpose a high-frequency,
very-low-voltage signal on top of the mains. |
|
| |
Brilliant, would work well for streetlights or even
warning sirens etc... [+] |
|
| |
Tweaking the entire power grid to get a weak time reference.... why not ? |
|
| |